Making a Guitar Mold - Eric Schaefer Guitars - Online Guitar Building School (2024)

5 дней назад

How to create a guitar mold from particle board, MDF or plywood. For the full guitar building course visit

www.ericschaeferguitars.com

Lesson Transcript: For this course, we are going to use an outside guitar mold. The mold is used during the side bending process and the soundbox assembly process. It also helps you mark out important dimensions in the early stages of the build.First, we will make a template.Then we will trace the template onto 3/4" MDF, plywood, or particle board and cut 6 sections.each section is then atteched to the original template for refinement on the router table.The 6 sections are glued together to create 2 pieces.Hardware is installed to hold the two pieces together and a wooden dowel is installed at the joints to keep the pieces properly aligned. For my template I am using half of a spare OM mold that I had in my shop, but you will have to create your own template from scratch, using your plans as a guide. To do this, trace half of your guitar's outline onto tracing paper.Stick the tracing paper to 3/4" particle board, MDF, or plywood with spray contact adhesive.Cut on the line with a bandsaw.I use a 1/4" blade or smaller so that it can handle the curves.Take your time and strive for consistent curves. All major inconsistencies can be smoothed out with 80 grit sandpaper wrapped around a wooden dowel. Minor inconsistencies can be ignored.As far as precision goes, the inside cut is what really counts. The outside cut can be rough cut to any shape as long as it is about 3 to 5 inches from the inside cut.Finally, drill 3 holes for use in mounting the template.Now this is actually just another piece from another mold that I have.I'm re-purposing it as a template for other molds.So, with that in mind, yours does not need to be as bulky as this is.In fact, you could just use a single piece of 3/4" plywood or something even thinner (half inch plywood would work just fine).That way, you could carefully, on a bandsaw, cut out the shape as precisely as you can. Because once you cut out that shape we are going to use that first template that you make, that should look something like this, to make the other pieces.There is going to be 6 pieces overall, 3 stacked on top of each other as you can see here. Having that template makes it real easy. We can make exact copies of each piece using the router with a guide bearing bit.So now we have our particle board out on the floor. And I'm going to use this template that I made here and trace out 6 copies of this.So instead of taking this straight to the bandsaw, because it is so big and cumbersome, we're going to first see if we can cut this up a little bit in place here using a jigsaw. You can use a circular saw. If you have a friend with you, you can take it over to the bandsaw, or the table saw.I am just going to break it down first this way into some slightly smaller pieces and then we can cut it on the bandsaw.Okay, now these are small enough to fit in the bandsaw.So we want to stay about 1/16" outside this line.That way, when we take this over to the router table, we will have very little wood left over for that router bit to remove.So we'll stay nice and tight to the line.Okay so now we are going to attach our template to the first piece, so that we can clean up those edges on the router table.So what I'm going to do is I'm going to hang this over the end like that, and line this up, so that the bottom piece is overhanging just slightly, everywhere.Okay, both sides are clamped. Let me just look around the edge and make sure we are overhanging a little bit.And I didn't drill any pilot holes. If you are using particle board or MDF you don't need to drill pilot holes.We can just drive those screws through and it won't split.So we are going to use a 1/2" straight cut bit with a guide bearing. That is what this little wheel is right here.And so I already have that set up in a good place. The guide bearing is up here against the template.Now remove the template, attach it to the next section, and continue routing until all 6 sections are complete.Okay so we've cut 6 of these. I'm going to pull 3 over to make our first half of our mold. We're going to hang this over the edge a little bit.What I first want to do, is very carefully take my time and get this lined up so that all the pieces are flush with each other.And I could check that with a square or something but I'm not going to. I can just feel for any overhanging edges. That is pretty good there.I carefully clamp this up, making sure it doesn't move. The whole purpose of this is that we are going to drill 2 holes here so we can have locating screws there to keep everything in alignment when we glue all these pieces together.Otherwise, if we put the glue on there without the locating screws, the whole thing will slide around in the glue once we tried to clamp it down. So this will help us maintain alignment....